Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Repair for Antioch Homeowners
A garage door that won’t open leaves your car trapped inside. One that won’t close leaves your house open to the street. Either way, you need it fixed by someone who works on doors every day, not a generalist who’ll figure it out once they’re standing in your driveway. Sawyer Garage Door Repair handles garage door repair in Antioch with technicians who have up to 11 years of experience and a specialty list that stops at doors and openers. That focus is why diagnosis tends to be quick and repairs tend to hold. Same-day service is often possible, and we answer 24/7. Call (866) 944-5178 and we’ll get you on the schedule.
Garage Door Spring Repair
Garage Door Spring Repair is the most common job we run in Antioch, and it’s the one you should never attempt yourself. Torsion and extension springs hold the entire weight of the door; when one snaps, the door becomes dangerously heavy and can drop without warning. You’ll usually hear a loud bang from the garage, and the door won’t lift more than a few inches. We replace the spring, balance the door, and test the opener’s travel limits before we leave. Typical cost is $180 – $340 for one spring. A matched pair is usually replaced together, so a pair runs about twice that range. The written estimate sets the final price.
Warning Signs of a Failing Spring
A visible gap in the coil is the clearest sign, usually a two-inch separation near the middle of a torsion spring. Doors that feel heavy when you lift them by hand, or that slam down instead of easing closed, are telling you the spring has lost tension. Don’t keep cycling the opener on a door like that; it strains the motor and the cables.
Why Springs Are a Professional Job
Torsion springs are wound under extreme tension, and the winding bars used to release that tension can slip with serious injury as a result. There’s no safe shortcut here. A trained technician has the right bars, the right springs for your door’s weight, and the judgment to know when cables or drums also need attention.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Sensor Repair
Garage Door Sensor Repair fixes the small photo-eye units mounted near the floor on each side of the opening, and it’s the first thing to check when a door reverses for no clear reason. The sensors beam an invisible line across the doorway; if that line is broken or the lenses are dirty or misaligned, the door won’t close. We realign the brackets, clean and test the lenses, check the wiring back to the opener, and replace a failed sensor when that’s the fix. Sensor work usually falls within our standard garage door repair range of $150 – $600, with the written estimate setting the exact price before we start.
What Interferes With the Beam
Sunlight hitting a sensor at a low angle can blind it, and so can a spider web or a leaf stuck to the lens. Bracket knocked slightly out of line by a bike or a recycling bin is another regular cause. All three produce the same symptom: the door starts down, then snaps back up.
When the Sensor Isn’t the Problem
If the sensors are clean, aligned, and their indicator lights are steady, the fault usually lives in the opener’s logic board or the wiring run along the ceiling. We test the circuit with a meter rather than swapping parts until something works, which keeps the bill down.
Emergency Garage Door Repair
Emergency Garage Door Repair covers the situations where waiting isn’t realistic: a door stuck half-open with the house exposed, a car locked in the garage, or a door that came off its track and is hanging crooked. A broken cable or a snapped spring can make a door unsafe to touch, so stop using the opener and leave the door where it sits. We answer 24/7 and run fast dispatch from 7am to 7pm, Sunday through Friday. Most urgent repairs land inside our $150 – $600 range, and you’ll have the written estimate before any work begins.
Making the Door Safe First
If the door is jammed open, don’t force it down by hand; a door with a failed spring can fall fast once it moves. Keep people and pets clear of the opening, and unplug the opener so nobody triggers it by accident. Then call and describe what you’re seeing.
What to Tell Us When You Call
The door’s material and rough width, the brand on the opener if you can read it, and what happened right before it failed all help us load the right parts. A photo of the spring or track sent to the technician’s number saves a trip back to the shop for a part.
Garage Door Panel Replacement
Garage Door Panel Replacement swaps out a single damaged section instead of the whole door, which is usually the smarter spend when the damage is localized. A backed-into bottom section, a dent from a basketball, or a panel bent when the door jumped track are all candidates. We match the panel profile and color to what’s already on the door wherever we can, and we check the hinges and rollers on that section while it’s apart. Typical panel work runs $250 – $500 depending on the section and material. The written estimate sets the final price.
Single Section or Full Door
A bottom panel is the most commonly replaced section because it takes the most abuse, and it’s also the one that carries the bottom seal and often the sensor brackets. If two or more panels are dented or the door is rusted through in places, replacement of the whole door starts to make more financial sense than patching.
Matching Color and Profile
Older Clopay and Amarr doors come in profiles that have changed slightly over the years, so a perfect match isn’t always available off the shelf. When it isn’t, we’ll show you the closest options and let you decide whether a close match is good enough or whether it’s time for a new door.
Garage Door Maintenance
Garage Door Maintenance is a tune-up that catches wear before it turns into a breakdown, and it’s worth doing once a year on any door in daily use. We lubricate the hinges, rollers, and springs, check the balance by hand, tighten the track and hardware, and test the opener’s force and travel settings. We also look at the weather seal along the bottom, which is what keeps rain and insects out. A maintenance visit typically costs $110 – $220 as part of our garage door repair range, and the written estimate confirms the price first.
What a Tune-Up Covers
The parts that wear fastest are the rollers, the hinges, and the springs, so those get the closest look. We also check that the door is balanced; a door that drifts down when you let go halfway is working the opener harder than it should. Small adjustments at this stage head off most emergency calls.
How Often to Book One
Once a year is the usual rhythm for a door that cycles a few times a day. If your garage is the main entry to the house and the door runs ten or fifteen times daily, twice a year makes more sense. Listen for new squeaks or grinding between visits.
Garage Door Roller Replacement
Garage Door Roller Replacement is a small job that makes a big difference to how quietly and smoothly your door runs. Rollers wear flat spots over time, especially the plastic kind, and a worn roller drags against the track and grinds. You’ll hear it before you see it. We replace the full set, inspect the hinges and track while the door is apart, and re-lubricate everything before testing. Typical cost is $110 – $220, and the written estimate sets the exact figure before work starts.
Metal Versus Nylon Rollers
Steel rollers last longer but run louder, while nylon rollers are quieter and gentler on the track, though they can crack in high heat. We’ll tell you honestly which fits your door’s weight and how often it gets used. There’s no single right answer for every garage.
Noise That Isn’t the Rollers
A grinding or scraping sound can come from a track that’s out of alignment or a hinge that’s come loose, not the rollers themselves. A quick look at the door’s travel tells us which; replacing rollers on a bent track won’t quiet it down for long.
Commercial Garage Door Repair
Commercial Garage Door Repair covers roll-up doors, sectional doors, and high-cycle operators on shops, storage units, and small warehouses around Antioch. Commercial doors run far more cycles per day than a home door, so springs, cables, and operators wear out faster and downtime costs money. We diagnose the failure, replace what’s worn, and check that the safety reversing system works as it should. Commercial work is quoted individually based on the door type and parts needed, and the written estimate is agreed before we touch anything.
High-Cycle Doors Wear Differently
A door that opens fifty times a day needs heavier springs and more frequent inspection than a home door that opens five times. Cycle count drives every wear decision on a commercial door. We ask how busy the bay is before recommending parts.
Safety Devices on Commercial Doors
Commercial operators use photo-eyes, sensing edges, and sometimes a combination, and a failure in any of them stops the door. We test each device and the wiring back to the control box. A door that won’t close on a busy morning is usually a safety device, not the motor.
Garage Door Cable Repair
Garage Door Cable Repair fixes the steel cables that run from the bottom corners of the door up to the drums, and it needs a professional because those cables are under the full tension of the springs. A frayed or snapped cable usually shows as a door that hangs crooked, with one side higher than the other. Never lift a door with a broken cable; the remaining cable can fail too. We replace both cables as a matched set, inspect the drums, and rebalance the door. Typical cost is $130 – $250, and the written estimate sets the final price.
Spotting a Cable Problem Early
Run your eye down the cable where it runs beside the door. Frayed strands, a kink, or rust are all reasons to stop using the door and have it looked at. A cable doesn’t usually snap without warning; it frays first.
Cables and Springs Fail Together
When a cable lets go, the spring on that side often takes the shock and fails too, and the reverse happens as well. We check both before quoting, so the price we give you covers the whole repair rather than half of it.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on LiftMaster and Chamberlain openers constantly; they share a lot of internal design, and the common failures in both are the logic board, the travel limit switches, and the gear assembly. Knowing where each one wears out saves diagnostic time. Genie operators show up in plenty of Antioch garages too, and their chain and belt drives need different handling from the screw-drive units.
On the door side, we’re fluent in Clopay and Amarr panels, which covers most of the sectional doors in the area. LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor are all makes we handle regularly, so whether you have a Clopay door or any other make, we can help. Call (866) 944-5178 to book a repair.
Signs You Need a Pro Right Now
- A loud bang from the garage. That’s usually a torsion spring breaking, and the door becomes very heavy right after. Stop using the opener and call before the door drops.
- The door reverses before it closes. Most often a sensor issue, but it can be the opener’s travel limit or a damaged cable. It needs a proper look before something jams.
- The door hangs crooked. One side lower than the other points to a stretched or snapped cable or a failing spring on one side. Running it like this puts stress on the whole system.
- Grinding or scraping as the door moves. Worn rollers, a loose hinge, or a track that’s out of line. Left alone, a dragging door damages the track and the opener.
- The opener runs but the door doesn’t move. Could be a stripped gear or a broken spring, or the manual release has been pulled. Once we’ve ruled out the simple causes, we test the drive and the door’s balance.
Our Process, Step by Step
- 1
You call and describe the problem. We ask what the door is doing, what brand the opener is, and when it started. That conversation routes the job to a technician who’s familiar with that system, and it’s often enough for us to bring the likely part.
- 2
We test the door by hand first. Before touching the opener, we disconnect it and check the door’s balance and travel. A door that’s heavy or drifts when released has a mechanical problem, not an electrical one, and the order of diagnosis matters.
- 3
We measure and inspect the moving parts. Springs, cables, rollers, hinges, and the track all get checked. We use a meter on sensors and opener wiring rather than guessing at parts.
- 4
You get a written estimate before any work starts. The price we agree on is the price on the invoice. Nothing is added after the fact and nothing gets done without your go-ahead.
- 5
We complete the repair and test everything. That means running the door through several full cycles, testing the safety reverse, and making sure the opener’s force settings match the door’s weight. Most repairs are finished in a single visit.
How Much Does Garage Door Repair Cost in Antioch?
A typical garage door repair in Antioch runs $150 – $600, and the exact figure depends on the part that failed and how accessible it is. A broken spring sits at $180 – $340 for one spring, with a matched pair about double that since they’re almost always replaced together. Cable work runs $130 – $250, roller replacement $110 – $220, and a single panel swap $250 – $500. Track realignment comes in around $120 – $240, and if the opener itself is the problem, repair is $120 – $320 while a full new opener install is $250 – $550. A complete new door, if you get to that point, is $700 – $2200.
What pushes a job toward the top of a range is usually door size and material, the condition of the surrounding hardware, and whether a stripped or rusted bolt turns this into a longer job. To avoid overpaying, ask for the part to be shown to you and get the estimate in writing before work begins. A detailed estimate should list each part, the labor, and the total. Our estimates are free, and the written estimate sets the final price.
Our Service Area Near Antioch
We cover Antioch and the towns around it, including Brentwood, Oakley, Clayton, and Discovery Bay, plus Blackhawk and Danville on the other side of the hills. If you’re further out toward Camino Tassajara or Contra Costa Centre, call and we’ll confirm the details for your address. Our coverage extends to garage door repair in Brentwood and garage door repair in Oakley, with the same free estimate and written pricing on every job. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday. Call (866) 944-5178.
Serving Antioch, CA – Our Local Coverage Area
We serve Antioch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Antioch
Garage door repair covers any fix to the door or its mechanism: springs, cables, rollers, panels, tracks, hinges, and the opener itself. It’s different from a new door installation, which replaces the whole system. We do both, so you’ll get a straight answer on which one makes sense for your door.
Most repairs take one to two hours on site. Spring and cable replacements are the most common jobs and generally run on the shorter side, while panel replacement and track work can take longer. We’ll give you a realistic time estimate when you call.
Most repairs fall between $150 and $600, and the final number depends on the part that failed. Springs run $180 – $340 for one, cables $130 – $250, rollers $110 – $220, and panels $250 – $500. Call (866) 944-5178 for an exact quote; estimates are free.
Yes, we service LiftMaster and Chamberlain equipment regularly, along with Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That coverage means we don’t need to send you to another company based on your brand. If your opener is one we don’t list, call and we’ll tell you honestly whether we can help.
Same-day service is often possible for repair calls. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (866) 944-5178 to check availability.
Our work is backed by a satisfaction guarantee. We stand behind the repair and the parts we install, and we’ll walk you through the details when you book. Ask your technician about coverage on the specific parts being replaced.
Clear the floor area around the door and make sure the technician can reach the opener unit. If you can, note the door’s brand and the model on the opener. Tell us ahead of time if the door is jammed open or off its track so we can come prepared.
Schedule Your Garage Door Repair Service in Antioch Today
A door that sticks or refuses to move won’t fix itself, and it usually gets worse. Call Sawyer Garage Door Repair at (866) 944-5178 for a free, no-obligation estimate on garage door repair in Antioch. We answer 24/7, dispatch from 7am to 7pm, and quote the price before any work starts. Whether it’s the door, the opener, or a full new installation, one call covers it.
Written by the team at Sawyer Garage Door Repair.